Generally, many people suffer losses caused by their vehicles. This is because of poor maintenance of these cars. Many believe that once the vehicle has been serviced mostly in the engine system that is the only way to increase the lifespan. However, this is part of maintenance but not the only one. Cleaning and washing thoroughly as well as offering emission system is very important. Ultra means engineering a project or a process in order to get maximum results. Therefore, Ultra wash car wash is not only a washing activity but also vehicle maintenance system.
This process undertakes certain steps in order to get the required satisfactory results. Before anything else is done, the vehicle is thoroughly rinsed. This step takes just a few minutes such as quarter an hour or less. This is where silts and dirt are removed. In order to avoid clogging of dirty materials in the wash mitt or sponge, a lot of water should be directed into the mint channels and gaps. In case rinsing is done by pressure washer or hose, it should also start from top heading downwards.
This step is followed by pre-washing where this stage deals mainly with the removal of light contaminants. These include things like road salts, grime bug splatter among others that affect the car paintwork appearance. If this process is not undertaken, these contaminants can cause marks and swirls later. This, therefore, interferes with the painting. Citrus power is the most common technique used in this section. This means the use of spray infused with citrus. It helps in collecting and lowering dirt over a paintwork.
During this stage, it is very important to pay attention to tighter and more intricate areas. These are places like fuel filter caps, door shut, grills and window rubbers among other places. Use of a brush with long bristles, in this case, is very important as grime and dirt from deeper areas are removed.
Main washing the follows up. It is characterized by the physical washing of the entire paintwork and vehicle. A sponge or a wash mitt and a shampoo solution is used. Two separate buckets or containers are used.
One of the buckets must be full of water and the other bucket you can put three- quarters water to leave enough capacity to add car shampoo. Add enough shampoo on the sponge and wipe the dust and contaminants stuck on the car paintwork. Permanent stains require patience because exerting pressure may end up destroying the car paint work.
After main washing, rinsing is done. This is done when washing or can be redone after finishing. If you are using a pressure washer or hose, the water should be set in way that there is a steady stream. It should be done from top heading downwards. If there is no pressure washer or hose, then use cans and pour water on top and let it flow downwards.
The last step is drying. This is also very important as this can cause negative effects on the paintwork. Use of water blades is highly discouraged as one step mistake can cause damage to the paintwork. The best material to use include microfiber towels. They also should be used in a gentle and careful way. Any scratch means polishing again which is an expensive activity.
This process undertakes certain steps in order to get the required satisfactory results. Before anything else is done, the vehicle is thoroughly rinsed. This step takes just a few minutes such as quarter an hour or less. This is where silts and dirt are removed. In order to avoid clogging of dirty materials in the wash mitt or sponge, a lot of water should be directed into the mint channels and gaps. In case rinsing is done by pressure washer or hose, it should also start from top heading downwards.
This step is followed by pre-washing where this stage deals mainly with the removal of light contaminants. These include things like road salts, grime bug splatter among others that affect the car paintwork appearance. If this process is not undertaken, these contaminants can cause marks and swirls later. This, therefore, interferes with the painting. Citrus power is the most common technique used in this section. This means the use of spray infused with citrus. It helps in collecting and lowering dirt over a paintwork.
During this stage, it is very important to pay attention to tighter and more intricate areas. These are places like fuel filter caps, door shut, grills and window rubbers among other places. Use of a brush with long bristles, in this case, is very important as grime and dirt from deeper areas are removed.
Main washing the follows up. It is characterized by the physical washing of the entire paintwork and vehicle. A sponge or a wash mitt and a shampoo solution is used. Two separate buckets or containers are used.
One of the buckets must be full of water and the other bucket you can put three- quarters water to leave enough capacity to add car shampoo. Add enough shampoo on the sponge and wipe the dust and contaminants stuck on the car paintwork. Permanent stains require patience because exerting pressure may end up destroying the car paint work.
After main washing, rinsing is done. This is done when washing or can be redone after finishing. If you are using a pressure washer or hose, the water should be set in way that there is a steady stream. It should be done from top heading downwards. If there is no pressure washer or hose, then use cans and pour water on top and let it flow downwards.
The last step is drying. This is also very important as this can cause negative effects on the paintwork. Use of water blades is highly discouraged as one step mistake can cause damage to the paintwork. The best material to use include microfiber towels. They also should be used in a gentle and careful way. Any scratch means polishing again which is an expensive activity.
About the Author:
Find a review of the advantages you get when you use Ultra Wash Car Wash Systems and more info about a reputable car wash equipment supplier at http://www.ultrawashsystems.com today.
0 commentaires:
Enregistrer un commentaire